三星CW28C7WG8XX_甜梦文库
三星CW28C7WG8XX
COLOR TELEVISION RECEIVERChassis : Model : KS3A(P) (REV. 2) CW28C7NG8XXEC CW28C7VDG8XXEC CW28C7VHG8XXEC CW28C7VHG8XXET CW28C7WG8XXEGCOLOR TELEVISION RECEIVERCONTENTS1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded Views and Parts List 7. Electrical Parts List 8. Block Diagrams 9. Wiring Diagram 10. Schematic DiagramsELECTRONICS? Samsung Electronics Co., Ltd. May.2001Printed in Korea 3KS3A-SEH-28C7-01Precautions1. PrecautionsFollow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.1-1 Safety Precautions1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people―particularly children―might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)LEAKAGE CURRENT TESTER(READING SHOULD NOT BE ABOVE 0.5mA)EARTH GROUNDFig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit’s AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields a these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called “horizontal disable” or “hold-down”.) Heed the high voltage limits. These include the XCray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.Samsung Electronics1-1Precautions1-1 Safety Precautions (Continued)9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs “integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently atta do not try to remove such “permanently attached” yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original―even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.1-2Samsung ElectronicsPrecautions1-2 Servicing PrecautionsWarning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecti always remove the instrument’s ground lead last.Samsung Electronics1-3Precautions1-3 Precautions for Electrostatically Sensitive Devices (ESDs)1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power― this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as “anti-static”; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.1-4Samsung ElectronicsReference Information2. Reference Information2-1 Tables of Abbreviations and AcronymsTable 2-1 Abbreviations A Ah ? dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k? km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M? m ?A ?F ?H ?m ?s ?W mA mg mH mI mm ms mV nF ? pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hourSamsung Electronics2-1Reference InformationTable 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor2-2Samsung ElectronicsReference Information2-2 IC Line UpTable 2 - 3 IC Line - Up NO BOARD LOC. NO IC201S IC601 IC901 IC902 IC602 HIC201 HIC202 HIC203 HIC204 HIC401 IC301 Q402 Q401 D414 IC401 1 MAIN Q404 IC801S D801S PC801S IC802 D805 D806 D807 D802 IC201 IC804 IC803 IC903 IC904 Q909 Q910 TU01S TU02S Samsung Electronics TCLS(S) TCPN3081PD09A(S) Main Tuner with IF Block Sub Tuner with IF Block Refer to Table 2-3-4 Refer to Table 2-3-5 2-3 FMG-G2CS KA78RM33 KA7806 KA78R08 KA78RM33 KIA7025AP 2NV Regulator 6V Regulator 8V Controlled Regulator 3.3V Regulator MICOM Reset IC IIC Level Shifter VDPY FML-G12S Rectifier Diode HC801 DDRI001 LA7845 KSC2073-H2 KSD5703 FMP-3FU KA393 IRF620 3S1265R RBV606 PC123Y KA78R05 SPS Controllor Bridge Diode Photo Coupler 5V Controlled Regulator E/W Drive IC Horizontal Drive IC HC401 100Hz Horizontal Pulse AMP Vertical IC Option DRGB001 RGB Drive AMP Hybrid IC SPEC VDP3112B MSP3411G SDA555X KS24L161 TDA7297 DESCRIPTION Video Processor Multistandard Sound Processor MICOM, TTX(MTP) EEPROM Audio AMP Refer to Table 2-3-3 VM Option REMARK Refer to Table 2-3-1 Refer to Table 2-3-2Reference InformationTable 2 - 3 IC Line - Up NO 1 BOARD MAIN LOC. NO T801S T444S IC501 IC502 2 CRT IC503 QF04 QF05 QG02 QG03 ICG01 3 4 5 DOUBLE FOCUS V-S/W PIP ICP02 ICH01 QH01 ICS01 ICP01 2SC11 KSA940 KSD2073-H2 KA4558 KA36RB TEA6425 SDA9489X EZ1086CM OP-AMP (TILT) OP-AMP TR-Power Video Switching IC with Adder Output High-end Picture-In Picture IC 3.3V Regulator Option Option Option Push-Pull (VM) Option TR-Power (TILT) TDA6111Q Video Output AMP R.G.B Drive SPEC AA26-00046A FUJ-29B001 DESCRIPTION Trans Switching Trans FBT REMARK Refer to Table 2-3-6 Refer to Table 2-3-72-4Samsung ElectronicsReference InformationTable 2-3-1 VIDEO IC (IC201S) SPEC VDP3108B VDP3112B VDP3120B VDP3130Y VDP3140D 50Hz Basic 50Hz, 2H Comb Filtr 50Hz, 2H Comb Filter, Horizontal Scaler 50Hz, 2H Comb Filter, DVD Input 100Hz FUNCTION REMARKTable 2-3-2 SOUND IC (IC601) SPEC MSP3400D MSP3410D MSP3411G Multistandard, A2 Stereo Multistandard, A2 Stereo, Nicam Multistandard, A2 Stereo, Nicam, Vitual Dolby FUNCTION REMARKTable 2-3-3 SOUND AMP (IC602) SPEC TDA7297 15W x 2CH, 10W x 2CH FUNCTION REMARKTable 2-3-4 1’st TUNER (TU01S) SPEC TCLS3101PD09A(S) TCPS3001PD09D(S) TCPS3001PD09E(S) Note CS with LNA Function CS CS India FUNCTION Main REMARKTCPS3001PD09A(S) is out-of-date, TCPS3001PD09D(S) which is up-to-date has the same function.Table 2-3-5 2’nd TUNER (TU02S) SPEC TCPS3000PC09B(S) CS FUNCTION Sub REMARKSamsung Electronics2-5Reference InformationTable 2-3-6 TRANS SPEC FUJ-29B001 FUH-29A001B 29” 21” FUNCTION REMARKTable 2-3-7 TRANS FLYBACK (FBT) SPEC AA26-00046A AA26-00044C 29” 21” FUNCTION REMARK2-6Samsung ElectronicsSpecifications3. SpecificationsTelevision SystemCS PAL/SECAM-B/G,D/K,L,I, NTSC-M 75ohms, Coaxial Cable 100W (Applied When 29” Flat) 220V Only Free Voltage Frequency 50/60Hz 15W x 2CH Output 10W x 2CH 5W x 2CH Vitual Dolby Effect Turbo Sound Pseudo Stereo RCA Input Front (AV2) S-VHS Head-PhoneOption Option 29 Inch 21 Inch Not Present R815Antena InputConsumptionPowerRequirementsSoundJacksBack2Scart Input/Output DVD Input(YPbPr) AV2 Monitor Audio Output S-VHSAV1 : Scart I/O, RGB Input, RF Out AV2 : Scart I/O, Monitor OutOption Option OptionSpecifications are subject to change. Specifications for Model Name (Ex. CS29A6??8X/HAC) Function N P PF PT PW MT NT WT GW NICAM 2 TUNER PIP 2 TUNER PIP, NICAM, TTX 2 TUNER PIP, A2 STEREO, TTX 2 TUNER PIP, A2 STEREO 2 TUNER MULTI PIP, A2 STEREO, NICAM, TTX A2 STEREO, TTX 1 TUNER PIP, A2 STEREO, TTX “NICAM” means that A2 STEREO + NICAM NOTESamsung Electronics3-1MEMO3-2Samsung ElectronicsAlignment and Adjustments4. Alignment and Adjustments4-1 General Alignment Instructions1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objecti if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.4-2 Automatic DegaussingA degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments.4-3 High voltage CheckCAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions.Samsung Electronics4-1Alignment and Adjustments4-4 Dynamic Focus Adjustment1. A dynamic focus adjustment should be done after replacing the CRT PCB, FBT or CRT. 2. Input a crosshatch pattern. ?3. Enter “ STANDARD “ in video mode. 4. Turn the Dynamic focus VR fully clockwise (maximum).(? ) 5. Turn the Static focus VR fully counterclockwise (maximum).(? ) 6. Slowly turn the static focus VR counterclockwise. Adjust until the vertical line in the middle of the screen has maximum clarity.(? ) 7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for maximum clarity.(? ) 8. Repeat 4-7, if necessary.??HSTATIC FOCUS VR?VDYNAMIC FOCUS VRSCREEN &FBT FOCUS PACK&4-5 SCREEN Adjustment1. Input Toshiba Pattern 2. Enter “Service Mode”.(Refer to “Service Mode”) 3. Select “G2-Adjust”. 4. Set the values as below. 29 Inch IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 21 Inch IBRM = 220 WDRV = 35 CDL = 165 COL = 704-2Samsung ElectronicsAlignment and Adjustments5. Turn the SCREEN VR until “MRCR G B” and “MRWDG” are green and those value are about 100. (The incorrect SCREEN Voltage may result that “MRCR G B” and “MRWDG” should be red)Note 1. When you do not have Toshiba Pattern, follow this method. 1. 2. 3. 4. 5. Set the TV on the condition that AV mode no signal(black) Enter the “Menu” and set the mode to blue screen off. Enter the “Service Mode”. Select “ G2-Adjust”. Set the values as below. IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 6. Turn the SCREEN VR until the value of “ MRCR G B” is about 120. Do not mind that the “OSD” Color is red.s After completing G2-Adjust, follow this procedure. x Enter the “Video Adjust 1”. ? Choose any item in menu. (ex. Select “Red Cutoff”) ? Change the value of item you select, and recover the value.For example, when the value of “Red Cutoff” is 127, change the value to 128 and restore the value to 127. If you do not follow this procedure, the picture may be abnormal. For example, when the TV set is on, the picture becames brighter gradually.Samsung Electronics4-3Alignment and Adjustments4-6 E2PROM (IC902) Replacement1. When IC902 is replaced, all adjustment data revert to the initial values. So, all adjustment values when servicing should be readjusted. 2. After IC902 is replaced, connect the AC power supply cord. 3. Turn the power switch ON. 4. In stand-by, warm up the TV for at least 10 seconds. 5. Power on the TV.4-7 White Balance Adjustments Equipment : Color-Analyzer (CA-100) s Input Signal : Pattern signal (Toshiba pattern) 1. Select STANDARD from the menu. 2. Input an 100% White pattern. 3. Enter the “Service Mode”. (Refer to “4-8 Service Mode”) 4. Warm up the TV set at least for 30 minutes. 5. Input a Toshiba pattern signal. 6. Enter the “Video Adjust1”. - Adjust “Sub Contrast” so that Y (luminance) becomes 40 ft ± 3. - Use “Red Drive” and “ Blue Drive” to adjust High-Light (x : 290, y : 300) - Adjust “Sub Bright” so that Y (luminance) becomes 1.3ft ± 0.3. - Use “Red Cutoff” and “Blue Cutoff” to adjust Low-Light (x : 290, y : 300). 7. Adjust CA-100 so that the final adjustment value can be fixed. 8. Use the Channel Up/Down (v/w) buttons to move the cursor on the adjustment modes. 9. Use the Volume +/- buttons to change the adjustment value.4-4Samsung ElectronicsAlignment and Adjustments4-8 Factory Adjustment4-8-1 Service Mode1. To enter the “Service Mode”, Press the remote-control keys in this sequence : - If you do not have Factory remote-controlPICTURE OFF DISPLAY ( ) MENU MUTE PICTURE ON- If you have Factory remote-controlPICTURE ON DISPLAY ( ) FACTORY2. After the Service Mode is entered, the initial screen is as shown in the figure below.Service Deflection Video Adjust 1 Video Adjust 2 Video Adjust 3 Option(81h 0Ch) Reset G2-Adjust Others*These hexa * depends on digits are check sum value which the MICOM. If check sum value is changed, the value of 2 E PROM Data newly initialed.3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters. Note 2. - When CRT, CRT PCB, FBT, E PROM (sometimes MICOM) is replaced, the adjustment values should be controlled. - After the Service adjustment is completed, Do not select “Reset” in the service mode menu. (After above procedure is done, power is on initially and the “Plug and Play” will be operated.)2Samsung Electronics4-5Alignment and Adjustments4-8-2 Memory Data4-8-2(A) DEFLECTION (GEOMETRIC ADJUSTMENT VALUE)Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OSD V Shift V Amp V Slope V SC H EW H Trapizium H Parabola H Symmetry H Corner H Shift PIP Contrast PIP Tint PIP PAL V Pos PIP NTSC V Pos PIP H Pos PIP BLKLG Range -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 0 ~ 15 0 ~ 63 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 15 Initial Value -30 -7 -3 -17 73 -47 -7 13 23 13 8 0 26 23 30 6 Function Adjust Vertical Picture Position Adjust Vertical Picture Size Adjust Vertical Slope Correction Adjust Vertical S-Correction Adjust Horizontal Picture Size Adjust Horizontal Trapeziod Adjust Horizontal Parabola Wave Adjust Horizontal Symmetry Adjust Horizontal Corner Adjust Horizontal Position Adjust PIP Contrast Adjust PIP Tinit Adjust PIP Vertical Position (Main Picture is PAL) Adjust PIP Vertical Position (Main Picture is NTSC) Adjust PIP Horizontal Position Adjust PIP Green Cutoff Level Not to be adjusted Not to be adjusted Remark4-6Samsung ElectronicsAlignment and Adjustments4-8-2(B) SCREEN CHANGE (I2C BUS GEOMETRIC ADJUSTMENT)1V Shift6V Amp2V Slope7V SC3H EW8H Trapizium4H Parabola9H Symmetry5H Corner10H ShiftSamsung Electronics4-7Alignment and Adjustments4-8-2(C) VIDEO ADJUST 1Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OSD Red Cufoff Green Cutoff Blue Cutoff Red Drive Green Drive Blue Drive Sub Bright Sub Contrast Sub Color Sub Tint BCL Threshold BCL Gain BCL Time TTX Contrast YC Delay Range Initial Value 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~ 200 0 ~ 13 0 ~ 27 0 ~ 100 0 ~ 255 0 ~ 15 0 ~ 15 0 ~ 255 0~8 127 127 127 127 127 127 100 50 27 80 65 8 9 90 * Adjust OSD/TTX Contrast Refer to Table 1 Adjust Beam Control Limit Refer to Note 3 Not to be adjusted Adjust Red Cutoff Level Adjust Green Cutoff Level Adjust Blue Cutoff Level Adjust Red Output Gain Adjust Green Output Gain Adjust Blue Output Gain Adjust Brightness Level Adjust Contrast Level Adjust Color Level Adjust Tint Low Light High Light High Light Low Light Function RemarkNote 3. Beam Control Limit CharacteristicbeamMIN 1.8mA 1.6mA BCL THESHOLD BCL GAIN MAXWDRGB50IRETable 1. YC Delay Adjustment Table YC Delay Value PAL Def. 4 BG 3 DK 6 I 6 L 7 Def. 1 BG 1 SECAM DK 5 I 8 L 5 NTSC Def. 4 M 3? The “Def.” means that TV is in AV mode.4-8Samsung ElectronicsAlignment and Adjustments4-8-2(D) VIDEO 2 ADJUSTFixed Value No. 1 2 3 4 5 6 7 8 OSD B stretch-BTHR B stretch-BTLT B stretch-BAM Coring? RGB Bright RGB Contrast EHT Time EHT Compensation Range 0 ~ 55 0 ~ 15 0 ~ 31 10 ~ 31 0 ~ 255 0 ~ 255 0 ~ 15 0 ~ 255 Initial Value 50 8 4 20 45 15 0 90 Black Stretch Threshold Black Stretch Tilt Position Black Stretch Amount Luma Peaking Filter Coring OSD/TTX RGB Bright OSD/TTX RGB Contrast Electronic High Tension Response Time Electronic High Tension Coefficient Function Remark? Coring : The Value of Center Frequency for the active bandwidth.4-8-2(E) VIDEO 3 ADJUSTNo. 1 2 3 4 5 6 7 OSD Peak Threshold Soft Limit Slope B Hard Limit Peak Video Ref Peak Video Gain Range Initial Value 0 ~ 255 0 ~ 15 0 ~ 255 0~4 0~5 185 4 255 0 0 33 39 Function White Peak Level Threshold Refer to Picture Below White Peak Level Threshold Reference White Peak Level Threshold Gain Auto Color Control Refer to Note Below RemarkACC-REF(PAL/NTSC) 0 ~ 40 ACCR(SECAM) 0 ~ 39Note 4. Soft Limit & Hard LimitOutput 511Part 1Part 2Slope 1 [0...15]Hard limiter0 2 4 6 8 10 12 14Slope 2 [0...15]4003002000 2 4 6 8 10 12 14Soft Limit Slope Brange=256...511? “Soft Limit” is that Limitting the peak white without feed-back, but “Peak Limit” is that with feed-back for white peak level100 tilt 1 [0...511] 0 0 100 200 300 400 500 600 700 800 900 tilt 2 [0...511] Li 1023Samsung Electronics4-9Alignment and Adjustments4-8-2(E) OPTIONFixed Value No. 1 2 3 4 5 6 7 8 9 Language Sound CRT AV Mode X-Ray Tilt Control Auto FM PIP Txt Language OSD Initial ? Value Arab, Iran, Lybya, CIS A2/NICAM, V-Dolby, Mono, L-Stereo 4:3, Wide, Q(12.8:9), 4:3-16:9, Q-16:9 2Scart, 2Scart+S, 1RCA, 2RCA, 2RCA+S, 2RCA+D, 2RCA+S+D, 1Scart Off, On Off, On Off, On 2-Tuner, 1-Tuner, Off Arabic, Farsi, Arab-Hebrew, West Europe, East Europe, Russian, Greek-Turkey Off, On Off, On Off, On Off, On Without “TV/VIDEO” key in the front panel, set to “On” When PIP is “2-Tuner”, set to “ON” Function Remark OSD LanguageDepending on IC601 Refer to Note 5S:S-VHS, D:DVD10 11 12 13LNA Equalizer High Deviate TTX On/Off14AV by CH keyOff, On? Initial Value : Refer to Note 6 on the next page.Note 5. Sound A2/NICAM V-DOLBY Mono L-Stereo MSP3400D, MSP3410D MSP3411G Not used this mode for KS3A Chassis IC6014-10Samsung ElectronicsAlignment and AdjustmentsNote 6. Option. CS29A5WT8X/UMG Description LANGUAGE SOUND CRT AV MODE X-RAY TILT CONTROL AUTO FM PIP TEXT LANGUAGE LNA EQUALIZER HIGH DEVIATE TTX ON/OFF AV BY CH KEY OPTION BYTE Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON OFF Arabic OFF ON ON ON ON 84 CC D8 CS29A6PF8X/HAC Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON 2-Tuner Farsi ON ON ON ON OFF 85 DC 5E CS29A6WT8X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON OFF RUSSIAN OFF ON ON ON OFF 83 AC 28 CS29A5MT9X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON 2-Tuner RUSSIAN ON ON ON ON ON 83 AC AE4-8-2(F) OTHERSFixed Value No. 1 2 3 4 5 6 7 8 OSD VSU H QEW H ZOOM Parabola H 16:9 Parabola TTX H Shift Range 96 ~ 111 -30 ~ 30 -30 ~ 30 -30 ~ 30 -30 ~ 30 Initital Value 98 0 8 -15 6 BG 2 8 Adjust Melody Volumn Adjust Horizontal Parabola in Zoom Mode Adjust Horizontal Parabola in 16:9 Mode Adjust Horizontal OSD/TTX Position Vertical Set Up Time Function RemarkMono Sound System BG/DK/I/M V Slice Level Melody Volumn 0~3 0 ~ 20Samsung Electronics4-11Alignment and Adjustments4-9 MICOM4-9-1 Pin LayoutWrite Protect EEPROM SDA EEPROM SCL Bus-Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V GND VDD 3.3V CVBS Input VDD 2.5V GND AFT Scart1 Ident Scart2 Ident Key 1 H-Sync V-Sync Key 3 Key 2 X-Ray Protect IR Input Stand-By LED Time LED1 2 3 4 5 6 7 8 9 10 11 12 13 14I/O I/O IO I/O I/O I/O I/O I/OPWM I/O I/O52 51 50 49 48 47 46 4515 ADC 16 ADC 17 ADC 18 ADC 19 20 21 I/O 22 I/O 23 I/O 24 I/O 25 I/O 26 I/OS D A 5 5 5 X44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 I/O 27Tilt N.C. Power Sound Mute N.C. N.C. PX. Y PX. Y VDD 3.3V GND VDD 2.5V CORE OSD-B OSD-G OSD-R VDD 2.5V GND X-TAL Out X-TAL In MICOM Reset N.C. N.C. VDD 3.3V GND N.C. Relay4-12Samsung ElectronicsAlignment and Adjustments4-9-2 Pin Assignment SpecificationPIN NO FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 I/O I/O I/O I/O I/O I/O I/O I/O Vdd GND Vdd CVBS Vdd GND ADC ADC ADC ADC HS VS I/O I/O I/O I/O I/O I/OASSIGN Write Protect ROM SDA ROM SCL Bus Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5VIN/OUT Out I/O I/O In I/O I/O Out OutACTIVE H/L LowDESCRIPTION EEPROM Write Protection EEPROM Serial Data Line EEPROM Serial Clock LineLowDisable Micom IIC Peripheral IC Serial Data LineLow LowPeripheral IC Serial Clock Line MSP IC Initial Control VDP IC Initial ControlVDD 3.3V CVBS Input VDD 2.5V In TTX CVBS Input Analog B+ Analog Ground AFT SC1-ID SC2-ID Key1 H-Sync V-Sync Key3 Key2 X-Ray IR-In STD-LED TIM-LED In In In In In In In In In In Out Out Auto Fine Tuning Control Scart1 Ident Scart2 Ident Key1 Input Horizontal Sync Input Vertical Sync Input Key3 Input Key2 Input X-Ray Protection Remocon Signal Input LED Drive Output(Red) LED Drive Output(Green)Samsung Electronics4-13Alignment and Adjustments4-9-2 Pin Assignment Specification (Continued)PIN NO FUNCTION 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 I/O N.C. GND Vdd N.C. N.C. Reset X-In X-Out GND Vdd R G B COR Vdd GND Vdd I/O I/O N.C. Not Used (Programmed Gound Level) N.C. I/O I/O N.C. I/O Tilt Out PWM S-Mute Power Out Out High Low Sound Amp Mute Picture On/Off Control Not Used (Programmed Gound Level) Tilt Control Output VDD 3.3V PX.Y PX.Y In When The Caption Function Adopted, Used. Out VDD 2.5V OSD-R OSD-G OSD-B CORE VDD 2.5V Out Out Out Out Reset X-TAL In X-TAL Out In In Out Low 6MHz 6MHz VDD 3.3V ASSIGN RelayIN/OUT OutACTIVE H/L LowDESCRIPTION Activate Degausssing Coil Not Used (Programmed Gound Level) Analog Ground Not Used (Programmed Gound Level) Not Used (Programmed Gound Level) Micom Hardware Reset Crystal Oscillation Input Crystal Oscillation Output Analog Ground Analog B+ OSD/TTX Output (Red) OSD/TTX Output (Green) OSD/TTX Output (Blue) Fast Blank/Half Contrast Output4-14Samsung ElectronicsPlug in Power CordSamsung ElectronicsON Check LED lamp OFF Normal Normal Check and Replace the MICOM Normal Check and Replace IC903 Check IC901 MICOM Input Voltage Abnormal Normal Abnormal Check the MICOM Power #59 With Remote Controller Replace the MICOM Abnormal Replace Q908 Normal Normal Check IC802, IC803 Replace IC802, IC803 Normal Check IC201S VDP H-OUT #50 Abnormal Replace IC201S Normal Check Q401 H-TR Replace Q401 Normal Check 135V Line Check PC801S, IC801S Normal Replace FBT Abnormal Abnormal Check R828 and D805 Abnormal Check IC801S and FP801S Normal Check and Replace R828 or D805 Abnormal Check IC804 Input Voltage Abnormal Normal Check and Replace IC804 Check D801 and D811 Abnormal Abnormal Replace D801 or D811 Check IC903 3.3V Regulator Input Voltage Normal Replace Q9085-1 No Power5. TroubleshootingAbnormalCheck MICOM IIC #5, #6Check Level Shifter Q909, Q910 Output(If 2N7000 Output has the DC Component over 0.7V, it is broken)NormalAbnormalCheck MICOM IIC #2, #3AbnormalReplace Q909, Q910NormalCheck IC902 EEPROMReplace EEPROM(IC902)NormalCheck IC201SNote : When you check whether any component is normal, you must let the output pin be open in order not to be affected by the side of output.Troubleshooting5-1No Picture, but sound is in normal operationNormalTurn the VR of FBT, higher screen voltage and Check the Deflection is in Normal Operation (If the deflection is in operation, flyback signal is appeared)AbnormalNormalCheck CRT PCB RK, BK, GKAbnormalNormalCheck IC201S #31AbnormalCheck Heater Voltage Abnormal Normal Check CRT and FBTCheck HIC202, HIC203, HIC204 OutputAbnormalCheck 8V Check IC201S #63 or #59 Normal Abnormal Normal NormalAbnormalCheck DZ202AbnormalCheck CRT and FBTNormalCheck IC803 Replace IC201S Check 200V, 16.5V Line Check Tuner CVBS Output Check IC301Replace DZ202Replace IC201S5-2 No PictureTroubleshooting5-2Samsung ElectronicsTroubleshooting5-3 No SoundNo Sound, but Picture is in normal operationNormalCheck the CN602 Connection and SignalAbnormalCheck the Speaker Wire ConnectionNormalCheck 14V LineAbnormalCheck IC602 #7 (If the pin is in low state, Sound is mute) NormalAbnormalCheck FA803SCheck D816, Q906 Check IC601 #24, #25 Normal Replace IC602 Check IC601 Input Voltages (5V,8V) Normal Check the coils around IC601 Check IC601 Input Signal Normal Replace IC601 Check the Tuner Abnormal Abnormal AbnormalSamsung Electronics5-3MEMO5-4Samsung ElectronicsExploded Views & Parts List6. Exploded Views & Parts List6-1 CW28C76-1Electrical Parts List7. Electrical Parts List7-1 CW28C7NG8XXECLevel Loc. No. Code No. D Specification Remark Level Loc. No. Code No. D Specification RemarkASSY-PCB,MAIN(OPT)0.1 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 V999S CN501A CN502A TOP IC501 *HA94-4-001105 AA39-20054B AA39-20053B AA39-20010B HA96-0-001687 AA62-00052A HA60-5-000129 AA26-0-001633 HA96-00275A AA62-0-2-001136 HA60-020007 AA60-3-000129 AA26-50001L AA40-00015A HA96-5-001064 AA62-30181F HA60-5-4-001775 AA26-3-1-6-6-6-000204 AA27-30001F AA27-00056A AA27-0-6-6-000318 AA29-30002N AA29-30002N HA96-5-000517 AA62-30180K HA60-5-000129 HA96-00274A HA60-020004 AA62-0-2-2-2-3-5-3-001697 HA96-0-000284 HA60-020007 AA62-0-3-001171 AA09-00135A HA96-50371C AA13-00101A ASSY-PCB,MAIN(OPT);CW28C7VN-703CN,KS3A/F SOCKET-CRT;11P,20PI,26.5PI,NI,LEAD CONNECTOR-ASSY;-,YBNH025-06,S,6P,500,1007#26 LEAD-CONNECTOR,ASSY;-,YBNH025-05,S,5P,500,1007#26 LEAD-CONNECTOR,ASSY;-,YFH800-01,S,1P,500,1617#22 ASSY H/S;-,VIDEO AMP,AA62-00052A,STV510 IC-VIDEO AMP;STV5109,ZIP,15P,-,SIGLE,50dB,P HEAT SINK-PS;,-,-,36*35*21,DC22,SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWRCH18 GREASE-SILICON;SC102,JAPAN TRANS SWITCHING;CODE-NO,CW6844N8X/XEF,-,AC90~2 IC-VIDEO PROCESS;VDP3112B,DIP,64P,-,PLASTIC,5V, ASSY-H/S;-,COMPLEX,AA62-00051A,KSD5703, HEAT SINK-PS;-,-,-,SILVER,HOLE 31mm,ALL, DIODE-RECTIFIER;FMP-3FU,1500V,5A,TO-3PF,ST TR-POWER;KSD5703,NPN,70W,TO-3PF,ST,8SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 WASHER-PLATE;M3,ID3.5,15X8.5,T1.0,-,SBHG,GREASE-SILICON;SC102,JAPAN TRANS-HORIZ.DRIVE;-,29mH,133uH,4.5uH,EI2218S,ST TUNER-F/S;TCPW3001PD09A(S),PAL/SECAM,TR, ASSY-H/S;-,-,AA62-30181F,TDA7297,IC-POWER AMP;7297,ZIP,15P,-,DUAL,32DB,PLAST HEAT SINK-ES;-,AL6063 EXTR.,2,WHT,50MM,SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 GREASE-SILICON;SC102,JAPAN IC-SOUND PROCESSOR;MSP3410D-C5 9458 ,SDIP,52P,-,P TRANS-FLYBACK;-,FUH-29A004,29,155V THERMISTOR-PTC;9OHM,+30%/-20%,220VRMS,270VAC, C-AL;330uF,20%,400V,GP,BK,30x45mm,1 C-FILM,MPPF;6.3nF,5%,1.6KV,TP,28.5x18x11.5 C-FILM,MPPF;7.2nF,5%,1.6KV,TP,28.5x18.5x12 C-FILM,MPPF;430nF,5%,400V,TP,26x20.5x12. COIL-LINEARITY;-,22uH,DR1011,PI0.45,25.5,-,20 COIL HORIZ. WIDTH;-,600uH,YL9N 15x27.5 C:9.5,0.1 COIL-HORIZ,WIDTH;-,10mH,YL-9N 15x27.5 C:9.5,0.3 C-FILM,MPPF;680NF,5%,400V,TP,26X14.5X24MM, C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm FILTER-LINE NOISE;-,16MH,1.5A,AC100~260V,28-16MH FILTER-LINE NOISE;-,16MH,1.5A,AC100~260V,28-16MH ASSY-H/S;-,-,AA62-30180K,LA7845,IC-VERTIVAL DEF.;LA7845,SIP,7P,-,PLASTIC,40V,11 HEAT SINK-ES;-,A6063 EXTR,-,WHT,50/13,-,-,SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 GREASE-SILICON;SC102,JAPAN ASSY-H/S;-,COMPLEX,AA62-00053A,FMLG12S SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWRCH18 HEAT SINK-PS;-,-,-,SILVER,HOLE 22mm,ALL, DIODE-RECTIFIER;FMG-G2CS,1000V,3A,TO-220F,ST DIODE-RECTIFIER;FML-G12S,200V,5A,-,DIODE-RECTIFIER;FML-G12S,200V,5A,-,DIODE-RECTIFIER;FML-G12S,200V,5A,-,IC-VOLTAGE REGULATOR;78R05,TO-220F,4P,-,PLASTIC,4. GREASE-SILICON;SC102,JAPAN IC-VOLTAGE REGULATOR;78R08,TO-220,4P,-,PLASTIC,7.8 ASSY-H/S;-,REGULATOR,AA62-00045A,KA7806 IC-POSI.FIXED REG.;7806,TO-220,3P,-,PLAS SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 HEAT SINK-PS;DP,-,-,-,AA62-00045A,-,-,-,-,GREASE-SILICON;SC102,JAPAN IC-EEPROM;24L161,16KBIT,DIP,8P,300MIL,10 IC MICOM;SIM806EW1-A040,CW29A6,52P,-0.3 ASSY-H/S;-,-,AA62-30181H,KA3A1265R,IC HYBRID;KA3A1265RD,CN5039,5Pin,-50to12T801S IC201S HC401 D414 Q401T401 TU01S IC602IC601 T444S PT801S C806 C405 C406 C426 L411 L408 L405 C423 CX801S CX802S ..2 LX801S LX802S ..2 IC301 ...3 ...3 ...3 ...3 ..2 HC801 ...3 ...3 ...3 D802 ...3 D805 ...3 D806 ...3 D807 ...3 IC802 ...3 ..2 IC803 ..2 IC804 ...3 ...3 ...3 ...3 ..2 IC902 ..2 IC901 ..2 IC801S ...3...3 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3AA61-10386A AA62-30197D HA60-020007 HA68-5-000129 IC903
L808 AA27-10002L IC401
HA98-2-2-4-4-000442 HA99-5
C211 BRACKET-IC;-,-,SECC 100,T1.0,-,KA2S0680,HEAT SINK-ES;DP,-,-,-,AA62-30181H,-,-,SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 LABEL-WARNING;A/P(90G),W33,H18,WHT GREASE-SILICON;SC102,JAPAN IC-POSI.FIXED REG.;78RM33,TO-220,3P,-,PL C-FILM,MPE-PPF;0.68nF,5%,1.6kV,TP,28x7x11mm,2 DIODE-BRIDGE;GSIB660,600V,6A,SIP-4,BKTR-POWER;KSC2073-H2,NPN,25W,TO-220,ST,6 PHOTO-COUPLER;TR,130-260%,200MW,DIP-4,ST THERMISTOR-NTC;4.7OHM,15%,MW,T C-AL;330uF,20%,200V,GP,ST,22x35,10 C-CERAMIC,DISC;4700pF,20%,400V,+20%~-55%,TP,2 JACK-SCART;42P,-,SN,BLK,NO C-AL;3300uF,20%,50V,WP,BK,18x35.5mm R-CEMENT;120ohm,5%,5W,CJ,TP,14x10x27mm COIL-CHOKE;-,24UH,K,-,2A,-,24UH-K,10X10MM IC-VOLTAGE COMP.;393,DIP,8P,300MIL,DUAL,36V,CMO FET-SILICON;IRF620,N,200V,5A,0.8ohm,50W,TO ASSY-SUB,PART;S51A,PCB-MAIN SOLDER-WIRE;S63S-W3.0,S63S,D3,SN63/PB37 SOLDER-WIRE FLUX;-,RS60S,D1.2,63SN/37PB FLUX;DF-96TVS,-,20%,SOLVENT;1M-H,96,ASSY-PCB,MAIN(ACI);CW..C7-3C,KS3A/F C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C-AL;3.3uF,20%,50V,GP,TP,5x11mm,5mm C-AL;3.3uF,20%,50V,GP,TP,5x11mm,5mm C-AL;3.3uF,20%,50V,GP,TP,5x11mm,5mm C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,-Samsung Electronics7-1Electrical Parts ListLevel Loc. No. Code No.D SpecificationRemarkLevel Loc. No. Code No.D SpecificationRemark...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3C212 C416 C213 C218 C219 C220 C221 C222 C223 C901 C921 C922 C919 C233 C234 C235 C907 C909 C237 C841 C604 C201 C303 C224 C225 C304 C305 C821 C902 C307 C302 C401 C403 C421 C402 C404 C408 C414 C418 C422 C424 C601 C610 C611 C415 C612 C613 C617 C917 C413 C622 C625 C626 C628 C707 C623 C624 C627 C629 C642 C644 C701 C638 C639 C632 C504 C505 C506 C634 C826 C832 C838 C637 C640 C641 C643
C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m C-FILM,PEF;33nF,5%,50V,TP,8.1x4.5x13mm,5m C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-AL;22uF,20%,16V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3mm,5m C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3mm,5m C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3mm,5m C-FILM,MPEF;220nF,5%,100V,TP,20x18x11.5,15 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5,5 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-AL;470uF,20%,25V,GP,10x16mm,5mm,T C-AL;470uF,20%,25V,GP,10x16mm,5mm,T C-FILM,MPEF;4.7NF,5%,400V,TP,-,5MM C-AL;220uF,20%,35V,GP,TP,10x12.5,5 C-AL;220uF,20%,35V,GP,TP,10x12.5,5 C-AL;47uF,20%,250V,HR,TP,13x25mm,5m C-CERAMIC,DISC;100pF,10%,500V,Y5P,TP,6x4,5 C-CERAMIC,DISC;470pF,10%,50V,Y5P,TP,5x3,5 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;1uF,20%,50V,BP,TP,5x11,5 C-AL;1uF,20%,50V,BP,TP,5x11,5 C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3C647 C649 C804 C805 C807 C814 C816 C817 C819 C822 C818 C910 C911 C913 C915 C918 C210 D201 D202 D207 D208 D209 D210 D211 D602 D804 DZ402 D906 D405 D501 D502 D503 D508 D604 KEZI D301 D411 D803 D816 D401 D404 D402 D403 D406 D810 D811 D907 D504 D413 D801 DZ201 DZ202 DZ802 DZ902 DZ601 DZ603 DZ903 DZ904 DZ905 DZ906 DZ907 DZ909 DZ910 DZ604 DZ605 DZ908 DZ203 DZ302 DZ303 DZ304 DZ305 DZ306 DZ804 DZ401 DZ801 DZ808
C-CERAMIC,MLC-AXIAL;56pF,5%,50V,SL,TP,1.9x3.5,C-FILM,PEF;1.5nF,5%,50V,TP,6.5x3.0x5.5mm, C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-FILM,PPF;2.2nF,5%,1.2kV,TP,15x8.5x13.5m C-CERAMIC,DISC;270pF,10%,2KV,Y5P,TP,8x6,7.5 C-AL;100uF,+30-10%,200V,HR,TP,16x25 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 C-AL;2200uF,20%,25V,WT,TP,16x25,7.5 C-CERAMIC,DISC;30pF,5%,50V,CH,TP,5.0x3.0,5mm C-CERAMIC,DISC;30pF,5%,50V,CH,TP,5.0x3.0,5mm C-AL;100uF,20%,16V,WT,TP,6.3x11,5 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-SWITCHING;1N0MA,DO-35,TP DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP DIODE-RECTIFIER;RG10V,400V,1.2A,DO-201,TP DIODE-RECTIFIER;1NA,DO-41,TP DIODE-RECTIFIER;1NA,DO-41,TP DIODE-RECTIFIER;1NA,DO-41,TP DIODE-RECTIFIER;1NA,DO-41,TP DIODE-RECTIFIER;1NA,DO-41,TP DIODE-RECTIFIER;1NA,DO-41,TP DIODE-RECTIFIER;RH1A,600V,0.6A,DO-204AC DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-204AC,TP DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DODIODE-ZENER;MTZJ6.8C,6.66-7.01V,500mW,DO-3 DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,DODIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,DODIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,DODIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,DODIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,TP DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,TP DIODE-ZENER;MTZJ15C,14.35-15.09V,500mW,DODIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO-3 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO-37-2Samsung ElectronicsElectrical Parts ListLevel Loc. No. Code No.D SpecificationRemarkLevel Loc. No. Code No.D SpecificationRemark...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3DZ805 GT101 GT102 GT301 GT302 GT401 GT402 GT801 GT802 GT803 GT804 GT805 GT806 GT103 GT409 GT501 GT502 GT503 J102 J103 J105 J108 J110 J111 J112 J113 J114 J115 J116 J117 J119 J122 J123 J124 J203 J205 J206 J207 J208 J209 J210 J212 J213 J214 J215 J216 J217 J218 J219 J222 J223 J224 J225 J226 J227 J228 J229 J230 J232 J234 J236 J237 J238 J239 J242 J244 J246 J247 J248 J401 J402 J404 J406 J409 J412 J414 J416 AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-40014A AA60-4-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-2-000219IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL,PLASTIC,2 PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO PIN-GT,ASSY;1P,-,-,AUTO WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3J418 J421 J422 J424 J428 J601 J602 J603 J604 J606 J607 J611 J614 J615 J616 J617 J618 J619 J620 J621 J622 J624 J627 J629 J631 J632 J703 J704 J709 J708 J715 J716 J717 J805 J806 J807 J810 J811 J816 J819 J820 J821 J822 J823 J824 J825 J826 J829 J830 J831 J832 J833 J908 J909 J911 J912 J913 J915 J916 J917 J924 J925 J926 J927 J928 J932 J933 J934 J936 J939 J941 J942 R939 J714 J249 D908 J835
WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mmSamsung Electronics7-3Electrical Parts ListLevel Loc. No. Code No.D SpecificationRemarkLevel Loc. No. Code No.D SpecificationRemark...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3J425 J633 J818 J612 L610 J937 J918 J626 J126 J118 J101 J253 J943 J944 J705 J707 J127 J410 J605 J608 J609 L107 J902 D407 R427 J503 J504 J506 J501 J502 J407 J419 J801 J802 J803 J804 J630 J245 L410 J221 R508 D509 J505 J507 J508 J509 J834 EY301 EY302 EY303 EY304 EY401 EY402 EY403 EY404 EY405 EY406 EY407 EY408 EY409 EY410 EY411 EY412 EY413 EY414 EY415 EY416 EY417 EY418 EY419 EY420 EY421 EY422 EY423 EY424 EY425
AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011AWIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,-...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3EY426 EY427 EY428 EY429 EY430 EY431 EY432 EY433 EY434 EY435 EY436 EY437 EY438 EY439 EY440 EY441 EY442 EY443 EY444 EY601 EY602 EY603 EY604 EY805 EY806 EY807 EY808 EY809 EY810 EY811 EY812 EY813 EY814 EY815 EY816 EY817 EY823 EY824 EY825 EY826 EY827 EY828 EY829 EY830 EY831 EY832 EY833 EY834 EY835 EY836 EY837 EY838 EY839 EY840 EY841 EY842 EY844 EY845 EY846 EY847 EY848 EY849 EY850 EY851 EY852 EY853 EY854 EY855 EY856 EY857 EY858 EY859 EY860 EY861 EY446 EY447AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011A AA60-40011AEYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD2.8,-,-,BST,EYELET;ID2.0,OD}